With the free POPP HUB smartphone and tablet app, you can control your home also from outside.ĭetailed instructions on the gateway can be found under the following link: Manual Prepare for Installation / Reset So, you can switch your sockets time scheduled, dim lights depending on current brightness or heat up your home to your comfortable temperature by only one push of a button. Other gateways block some device functions by itself.īy using so-called apps from the continuously growing app store, you can setup a lot of automation scenes in no time. The POPP HUB?s big advantage is its capability to integrate all certified Z-Wave devices with all of theirs functions. Thanks to the integrated device database and step-by-step instructions any new smart home device can be connected quick and easy. Therewith it is one of the most secure smart home gateways generally. The POPP HUB is focused on easy operation and reliable security architecture. The HUB works with Z-Way, the fist Z-Wave Plus certified Z-Wave controller software, which also connects devices with different technologies with each other. The POPP HUB enables you to control your home centralized and flexible ? and without any wiring effort. Beside already installed WiFi and Z-Wave technologies the HUB can integrate further technologies such as EnOcean via internal and external USB ports. The latest POPP HUB hardware generation is still more flexible. These associations can be used also without a central gateway. Inside one network the POPP HUB controls up to 230 Z-Wave components manufacturer-independently and allows management of direct connections (associations) between the devices. Therewith you can control your whole home automation network via remote switches, smartphone, desktop and tablet pc. The second-generation POPP HUB is a slim and compact IP smart home gateway, equipped with Z-Wave wireless technology. But all these components need a central controller. Sensors, switches, thermostats, cameras and many devices more will make you home intelligent. Otherwise it will automatically turn into a lower level of security to maintainįor more information about Z-Wave technology, devices, white papers etc. Secure as long as this device provides the same or a higher level of security. If a device supports secure communication it will communicate with other devices This device and every other certified Z-Wave device can be used together with any otherĬertified Z-Wave device regardless of brand and origin as long as both are suited for the ( meshed network) in case the receiver is not in direct wireless range of the Z-Wave ensures a reliable communication by reconfirming every message ( two-wayĬommunication) and every mains powered node can act as a repeater for other nodes Thisĭevice is suited for use in the region mentioned in the Quickstart section. Z-Wave is the international wireless protocol for communication in the Smart Home. Follow the disposal instructions.ĭo not dispose of electronic equipment or batteries in a fire or near open heat sources. Use this equipment only for its intended purpose. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Failure to follow the recommendations in this manual may be dangerous or may violate the law. Please go to -> Setup -> Applications -> Active and change settings in "Time Zone and Access from WAN" app. You can later change your device‘s time zone and allow access to the hub user interface via the Ethernet address. To add your first Z-Wave device, go to -> Configuration -> Devices -> Z-Wave -> Add New and follow the instructions.Ĩ. Start adding Z-Wave devices and apps and have fun. Now you can access your controller from outside your home, too, using the service. Make sure not to un-power the device during the firmware update.Ħ. In case there is a firmware update you will see a message screen. Remember it for remote access! Define your access password for the default login name ‘admin’ and your email for password recovery, set your time zone and LAN access (otherwise you can only access using and using WIFI).ĥ. The welcome screen displays your unique device ID. If you use a mobile device, install and start the Popp HUB app (Use the QR code on page 4).Ĥ. Attention: For security reasons, the initial configuration is available via WIFI only. Now you can connect your computer or mobile device to the new WIFI Popp-xxxx (xxxx=last 4 digits of MAC address displayed on device label, WIFI-password on label, too). After up to 2 minutes the HUB is ready to use and the white LED will breathe normal. Connect the HUB to your local network using Ethernet cable.Ģ. To run this device please connect it to your mains power supply.ġ.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |